Available models:
NetAir 900 (without internal antenna, N jack connector)
NetAir 900-A (includes internal antenna)
Interfaces and Connections:
LAN
1 x (RJ-45) 10/100 Base-TX half/full duplex IEEE 802.3u
Power over Ethernet (compliant with IEEE 802.3af)
Impedance: 100 ohms
1 x RJ-45 connector with LED indicators
CAT-5e STP (EIA/TIA-568-B) cable: 100m maximum (recommended)
WAN: Radio interface
Unlicensed radio band of 900 MHz
Bandwidth: 5 and 10MHz
Frequency range:
• 907MHz (5MHz bandwidth)
• 912MHz (5MHz bandwidth)
• 917MHz (5MHz bandwidth)
• 922MHz (5MHz bandwidth)
Radio Technology:
OFDM (Orthogonal Frequency Division Multiplexing)
User channel selection
User configured transmission power
Data rate (air interface):
6M, 9M, 12M, 18M, 24M, 36M, 48M, 54Mbps (OFDM)
Maximum Transmission Power:
• 6~18Mbps: +28dBm
• 24~54Mbps: +17dBm
RSSI association threshold
• 6Mbps: -87dBm
• 9 Mbps: -86 dBm
• 12 Mbps: -86dBm
• 18 Mbps: -83dBm
• 24 Mbps: -79dBm
• 36 Mbps: -76dBm
• 48 Mbps: -70dBm
• 54 Mbps: -67dBm
Air interface security
WPA1 and AES 128 cryptography
MAC address filtering enabled (only network clients with allowed addresses will be able to join the network)
Residual protection against attacks and intrusion
Other Security Features:
Stateful Firewall: stateful packet inspection, blocking and allowance of traffic based on the connection state.
Packet filtering by source port, interface, MAC address, IP source address, IP destination address, protocol, type of TCP packets and flags
2 level password protection for access
Antenna:
NetAir 900 (without internal antenna)
1 x female N-type 50 ohms connector for external antenna
NetAir 900A (includes internal antenna)
Gain: 9dBi
Polarization: either vertical or horizontal
VSWR: 1.5:1 (maximum) |
|
Configuration and Management:
HTML based Graphical User Interface for management (either local or remote equipment configuration and monitoring)
Telnet (both local and remote equipment configuration and management)
Configuration wizard
SNMPv1, SNMPv2 and SNMPv3 agents with support to MIBII (RFC-1213) and iFTable
Remote firmware update via FTP and HTTP
Management interface through VLAN
Scantool - mechanism that searches Parks equipment in the network and identifies IP address of each one.
Operational features:
Modes of Operation
Bridge or Router
Master or Slave (selection through software)
Routing:
• RIPv1 (only network class masks)
• RIPv2
• Static routing
VLAN pass-through
QoS layer 3
Classification and marking of packets
DiffServ for prioritizing classified packets
Hierarchical Token Bucket (HTB)
Traffic Shaping
Priority Scheduling
Address management:
• NAT
• NAPT
Environmental and Mechanical Features:
Operating Temperature: 0°C to 60°C
Enclosure: Outdoor
Ingress Protection (IP) rate 65
Connectors with outside access protected by coating
Internal antenna (NetAir 900A)
Flexible mounting kit suitable for either wall or pole allowing best adjustment of the antenna, both Azimuth (horizontal plan) and Zenith (vertical plan)
Integrated pressure compensation/ventilation valve for avoiding early degradation of electronic components and humidity within the radio device.
LEDs
RJ45 - Power indicator
Installation tools:
Audible antenna alignment indicator
Software (command or Web) indicator of signal strength for helping antenna alignment
Configuration wizard
Power supply:
High Power Over Ethernet (HPoE) Adapter: 56V @ 550mA56V @ 550mA |
